• 产品特点
  • 技术规格

 双缸、四冲程、水冷、纯电启动发动机

 采用DOHC、滚子摇臂技术(提高配气机械效率,降低损失)

 采用直线进气道、双缸八气门技术(减少进气流动损失与进气口积碳,提高充气效率,使动力性能更好)

 采用双缸180°全平衡曲轴及内置单平衡轴技术(降低振动)

 初级齿与平衡齿采用主副齿轮结构,消除齿间侧隙(降低齿轮噪声水平)

 初级齿与平衡齿采用磨齿技术,进一步提高齿轮精度(减小啮合噪音)。

 曲轴采用轴瓦结构,运转声音更小(噪音小、降低磨损,提高寿命)

 采用小体积高性能起动电机(电起动声音小)

 优化设计换挡机构、传动机构,使其变速机构更紧凑、更可靠,换挡平顺过渡性好,更舒适。(换挡更省力、到位感与舒适性更好)

 离合器采用4组主弹簧、7片大直径摩擦片结构(进口FCC纸基摩擦片,离合器更可靠,残余力矩小、分离性更好) ;另外可选配最新设计的滑动离合器,骑乘舒适性将进一步提升(舒适性好)

 离合器采用三级减震技术,能有效吸收冲击(齿轮啮合平稳,声音品质及可靠性更高)

 双缸180°异步点火,发动机运转更平稳(振动感更小,长时间骑行舒适性好)

 活塞轻量化+裙部储油槽设计(降低磨损,大幅增加活塞寿命,减少机油消耗)

 活塞环采用PVD强化处理(更耐磨,机油消耗低)

 采用活塞强制背冷技术(活塞散热快,热负荷低,寿命更长)。

 优化设计水套结构,消除水流死角,尽量延长水套路径带走更多热量(散热效果更好,降低缸头温度,提高发动机寿命)

 气缸内壁采用平台网纹(降低初期活塞、活塞环磨损)

 采用调整垫片取代调节螺钉方式来驱动气门,点面接触换成了线面接触,磨损更小,气门间隙变化小(减少气门间隙维护)

 外置精滤器结构(更换滤芯更方便)

 采用缸头与水泵水路小循环设计,实现快速暖机(低温环境快速起动)

 

 Two-cylinder, four-stroke, water-cooled, electric starting engine.

 DOHC, roller rocker arm technology (improve valve mechanical efficiency, reduce losses).

 Adopt linear inlet, double cylinder eight valve technology (reduce intake flow loss and intake carbon deposit, improve charging efficiency, make power performance better).

 Double cylinder 180° fully balance crankshaft and built-in single balance shaft technology (vibration reduction).

 Primary and balance teeth adopt the main and counter gear structure to eliminate the side backlash between teeth (reduce gear noise level).

 Grinding technology is adopted for primary teeth and balance teeth to further improve gear accuracy (reduce meshing noise).

 The crankshaft adopts the bearing shell structure, and the running sound is smaller (less noise, less wear, and more life).

 Small size and high performance starting motor (electric starting sound is low).

 Optimize the shift mechanism and transmission mechanism, so that the transmission mechanism is more compact and reliable, and the shift smooth transition is good and more comfortable. (Less effort in shifting, better sense of position and comfort).

 The clutch adopts 4 groups of main springs and 7 large diameter friction plates (imported FCC paper-based friction plates, the clutch is more reliable, the residual torque is small, and the separation is better).

  In addition, the latest design of the sliding clutch can be selected to further improve the riding comfort (comfort is good).

 The clutch adopts three-stage shock absorber technology, which can effectively absorb shock (smooth gear meshing, higher sound quality and reliability).

 Dual cylinder 180° asynchronous ignition, more stable engine operation (less vibration, long ride comfort).

 Lightweight piston + apron tank design (reduces wear, greatly increases piston life and reduces oil consumption).

 Piston ring reinforced with PVD (more wear resistant, lower oil consumption).

 Adopt piston forced back cooling technology (piston heat dissipation fast, low heat load, longer life).

 Optimize the design of the water jacket structure, eliminate the dead angle of the water flow, and extend the water jacket path to take more heat (better cooling effect, reduce the cylinder head temperature, and improve the engine life).

 Cylinder inner wall with platform mesh (reduce the initial wear of piston and ring).

 The valve is driven by adjusting gaskets instead of adjusting screws, and the point contact is replaced by line contact, which has less wear and less change of valve clearance (reduces valve clearance maintenance).

 External fine filter structure (more convenient to replace filter element).

 Small circulation design of cylinder head and water pump to achieve fast heating (fast start in low temperature environment).

外特性曲线 WIDE OPEN THROTTLE CURVES

悬挂图 INSTALLATION DIMENSIONS

Copyright © 2014 loncinengine.com All Rights Reserved
电话:400 636 9980 地址:重庆市九龙坡区九龙工业园C区聚业路116号 邮箱:Engine_loncin@sina.com 传真:86 23 8669 3433